Code

What we go by

Every insulation and drywall job we do is built to the current North Carolina State Building Code, which right now means the 2018 NC Residential, Building, and Energy Conservation Codes. Below is a plain-English summary of the parts that matter for insulation and drywall, with links to the official code books.

Last reviewed November 2026.

Which books are in effect

The NC Office of State Fire Marshal lists the 2018 codes as the ones in force since January 1, 2019. They include North Carolina’s amendments. The free official text is on the ICC site:

Later amendments are published separately. The residential amendment list and the energy amendment list are on ncosfm.gov. We did not find an amendment that changes the foam-plastic, gypsum-board, or garage-separation sections summarized here. Townhouse separation was amended, and that note is below.

The 2024 North Carolina codes are adopted. They are not in effect. The original date slipped, and the State Fire Marshal’s letter on the effective date was still current in November 2026. The 2018 books are the ones we build to unless an owner is approved to use 2024 early. The 2024 books are online for reading only: residential, building, and energy.

Insulation

Climate zones

Table N1101.7 (R301.1) puts Buncombe and Henderson counties in Climate Zone 4A. Haywood, Madison, Transylvania, and the other nearby counties on that table are 4A as well. Alleghany, Ashe, Avery, Mitchell, Watauga, and Yancey are Zone 5A. Asheville and Hendersonville are Zone 4. Those high-mountain counties need a bit more insulation in walls and floors.

Zone 4 R-values

The minimums in Table N1102.1.2 (R402.1.2) are the floor, not a target we stop at. Many of the houses we do go past them.

Minimums from the 2018 residential energy table
Part of the house Zone 4 Zone 5
Ceiling or attic R-38, or R-30 continuous R-38, or R-30 continuous
Wood-frame wall R-15, or R-13 plus R-2.5 continuous R-19, or R-13 plus R-5, or R-15 plus R-3
Floor R-19 R-30, or fill the cavity, R-19 minimum
Basement wall R-10 continuous or R-15 in the cavity Same
Slab edge R-10 R-10
Crawlspace wall R-10 continuous or R-15 in the cavity R-10 continuous or R-19 in the cavity

Two footnotes on that table matter on real houses. Full-height R-30 that runs over the top plate at the eaves can meet the ceiling number. R-19 batts compressed into a 2×6 wall can count. They do not count that way in a 2×4 wall. Where a cathedral ceiling has no room for R-38, R-30 is allowed for a limited area (N1102.2.2). Attic hatches are weatherstripped and insulated (N1102.2.4). Floor insulation stays against the subfloor (N1102.2.8).

Air sealing and the blower door

N1102.4 (R402.4) says a new house has to show it is air-sealed. That is either a visual checklist or a blower-door test at 50 pascals. The test number in the book is 5 air changes per hour or less, or a surface-area alternative. The test comes after the envelope penetrations are in. Spray foam is how we usually get a tight shell. Every spray foam house also includes a complimentary REScheck.

Certificates

N1101.10 (R303.1) and N1101.14 (R401.3) call for a signed insulation certificate and a permanent energy certificate. We post what was installed and its R-value. On spray foam, the certificate lists thickness and installed R-value. Blown attic insulation gets depth markers. The permanent card usually lives at the electrical panel.

Spray foam and fire protection

R316 is the residential rule for foam plastic. Foam is not left bare in living space. It is separated from the room by a thermal barrier. Half-inch gypsum board is the usual one. A material that passes the NFPA 275 tests is the other listed route.

In an attic or a crawl that people enter only for service, the book allows a lighter ignition barrier, or a foam system tested for that use (R316.5.3, R316.5.4, and R316.6). The commercial counterpart is NC Building Code Chapter 26, sections 2603.4 and 2603.4.1.6. Drywall is still the cover we hang in lived-in rooms. Where the foam stays exposed, the coating section below is the other path.

Sealed crawlspaces

R409 is North Carolina’s closed-crawl chapter. A sealed crawl is closed to the vents, has a ground vapor retarder, and has a way to dry the air. Insulation can be in the floor or on the walls. If the crawl is intentionally conditioned, the insulation goes on the walls, including the band joist. Foam on the inside of those walls keeps a termite-inspection gap below the sill and a gap above the dirt or slab (R409.8.1.1). Foam left uncovered there has to meet the flame-spread and smoke limits in R409.8.2, or it gets a protective cover. Foam in a crawl used as conditioned space or as a plenum needs an approved thermal barrier. A vented crawl, under R408, is insulated in the floor.

Drywall

Fasteners, thickness, and moisture

R702.3 is the residential gypsum-board section. We hang to the spacing and thickness in that table: tighter fastening on ceilings, and thicker board where a ceiling gets texture or the framing is 24 inches on center. Screws have to bite into the wood. Board used as a backer for tile has to be a listed moisture-resistant product. Water-resistant gypsum backing board does not go over a Class I or II vapor retarder in a tub or shower, and it does not go where water hits it directly. That is where a cement or glass-mat backer belongs.

Garage separation

R302.6 asks for gypsum board between an attached garage and the house. The garage side of walls and ceilings next to the house is at least half-inch board. Under living space above the garage, the ceiling is at least five-eighths-inch Type X. That is standard on an attached-garage job. Enclosed space under stairs gets half-inch board as well (R302.7).

Townhouses

The January 1, 2023 amendment to R302.2 changed how townhouses are separated. With a sprinkler system, the separation can be two 1-hour walls or one 1-hour common wall. Without sprinklers, the common wall is 2-hour. Rated walls are built the way the tested design lists them: board type, layers, fasteners, and joint treatment, tight to the sheathing and the roof deck, with no plumbing or ducts in that cavity. The amendment list is on ncosfm.gov.

Commercial drywall

On commercial work, gypsum board follows NC Building Code Chapter 25: install to GA-216 and ASTM C840, keep the board out of the weather, and treat joints and fasteners on fire-rated assemblies. Insulation and the air barrier on those buildings follow the commercial energy code. At the thicknesses in that chapter, closed-cell and open-cell spray foam can count as the air barrier when the joints are sealed.

Intumescent coatings over spray foam

In some attics, crawl spaces, mechanical rooms, and commercial spaces, spray foam can be protected with a sprayed-on intumescent coating instead of drywall. North Carolina allows that only when the foam-and-coating pair has been fire-tested and listed together. The coating is listed and tested with the specific foam product, applied at the tested thickness, and the foam is no thicker than the assembly that was tested. Occupied rooms use a thermal-barrier test. Attics and crawls entered only for service can use the ignition-barrier path, including the ICC-ES AC377 Appendix X test. We follow the evaluation report, post the certificate it asks for, and the local inspector signs off. A coating does not turn an attic into living space or storage.

The criteria live at ICC-ES AC377. The residential triggers are R316.4, R316.5.3, R316.5.4, and R316.6. The commercial triggers are in Chapter 26. More of how we use the coating is on the intumescent coatings page.

Your local inspector has the final word

These notes are a map of the books, not a substitute for them. The official text is at ncosfm.gov and codes.iccsafe.org. Your local inspector has the final word.

We guarantee your insulation passes inspection. If it does not, we'll make it right.

Last reviewed November 2026.

Estimate

Ready for a price? Call, send plans, or ask online.

Mon–Fri 8–5, call anytime for a return call